Toyopuc Error Codes
| Error code (Decimal) |
Error code (Hex) |
Meaning |
|---|---|---|
| 0 | 0x000 | No Error |
| 17 | 0x011 | Inability to process data because of faulty CPU Module Hardware |
| 32 | 0x020 | Fixed Data (ENQ) within relay command is not 05. |
| 33 | 0x021 | Faulty transfer number |
| 35 | 0x023 | Erroneous command code |
| 36 | 0x024 | Erroneous subcommand code |
| 37 | 0x025 | Erroneous command-format byte |
| 38 | 0x026 | Erroneous function call operand number |
| 49 | 0x031 | Write of function call prohibited by sequence operation |
| 50 | 0x032 | A command that is defeated during a stop continuity is activated during a stop continuity |
| 51 | 0x033 | Attempting to execute a debug function despite non debug mode |
| 52 | 0x034 | Access prohibited due to configruation |
| 53 | 0x035 | Non-executable due to configuration |
| 54 | 0x036 | Non-executable due to other device configuration |
| 57 | 0x039 | Attempting to start scanning without any reset afterwrting I/O point number parameters |
| 60 | 0x03C | During a fatal failure a command has issued that is not executable during a fatal failure |
| 61 | 0x03D | Non-executable due to competing process with a different-factor command is executed |
| 62 | 0x03E | Non-executable command due to reset existence |
| 63 | 0x03F | Non-exectuable command due to stop duration |
| 64 | 0x040 | Address of a reading/writing command or address + data number of a command is out of range |
| 65 | 0x041 | Word/byte number is out of range |
| 66 | 0x042 | Non-designated data is sent |
| 67 | 0x043 | Erroneous function-call operand |
| 82 | 0x052 | Though any timer or counter is employed a command for reading.writing the set/recent values is issued. |
| 102 | 0x066 | No reply is sent from link module with the link exchange number specified by a relay command |
| 112 | 0x070 | Non-executable module with the link exchange number specified by a relay command |
| 114 | 0x072 | No reply is sent from link module with the link exchange number specified by a relay command |
| 115 | 0x073 | Multiple relay commands were issued to the same link module |
| 512 | 0x200 | Timed Out Waiting for Response from Remote |
| 513 | 0x201 | Timed Out Waiting for Echoed Message |
| 514 | 0x202 | Unexpected Device Response |
| 515 | 0x203 | Mismatch Response Command Code |
| 516 | 0x204 | Relay Command: Exchange Number Mismatch |
| 517 | 0x205 | Relay Command: Wrong Number of Hops |
| 768 | 0x300 | No Error |
| 769 | 0x301 | Port Not Defined |
| 770 | 0x302 | Port Failed To Connect |
| 771 | 0x303 | Port Lost Connection |
| 772 | 0x304 | Serial Port Settings Out of Range |
| 773 | 0x305 | Serial Port Already In Use or Not Available |
| 774 | 0x306 | Serial Port Access Denied |
| 775 | 0x307 | Serial Port General Failure |
| 776 | 0x308 | Serial Port Invalid Parameter |
| 777 | 0x309 | Port Not Connected |
| 784 | 0x310 | Port Unknown Error |
